header
Image from OpenLibrary

Stress analysis of two different attachments for a single implant retained mandibular overdentures in the midline : In vitro study / Ahmed Hasanin Mohammed Rashad ; Supervised Hamdy Abou Elfotouh Hamed , Nouran Mahmoud Abdelnabi

By: Contributor(s): Material type: TextTextLanguage: English Publication details: Cairo : Ahmed Hasanin Mohammed Rashad , 2020Description: 81 P. : charts , facimiles ; 25cmOther title:
  • تحليل القوة بواسطة نوعين مختلفين من انظمة الربط للأطقم الفوقية السفلية لغرسة واحدة فى خط المنتصف : دراسة معملية [Added title page title]
Subject(s): Available additional physical forms:
  • Issued also as CD
Dissertation note: Thesis (M.Sc.) - Cairo University - Faculty of Oral and Dental Medicine - Department of Prosthodontics Summary: Aim: The aim of this in vitro study is to record the induced micro-strain around one installed implant in the midline of a completely edentulous mandible using strain gauges utilizing an implant retained overdenture with two different types of attachments Ball and CMLOC attachment. Methodology : An acrylic resin test resin test model representing a completely edentulous lower arch was used The distal part of the residual ridge was covered with silicon based soft liner to stimulate the mucopcriostcum. Steps of complete denture fabrication was followed in conventional manner .Duplication of the finished denture was carried out to be used as a surgical stent .A single implant installed in the midline.After the implant was installed in the acrylic resin cast, the ball attachment was screwed to the implant.The denture was prepared for the direct pick up procedure, the same procedure repeated for CM IOC attachment. Four strain gauges around were installed on all surfaces of implant (Buccal. Lingual. Mesial .Distal) to monitor the effect of the applied loads vertical on the two types of attachments. A vertically load applied of 100 N static load was applied by using universal testing machine at three different sites (unilateral right first molar central fossa, left first molar and bilaterally. Results: When the load applied on the right side and left side ,it was shown that the single implant retained ovcrdenture with ball the attachment has shown higher microstrain than the CMLOC ,average microstrain for CMLOC ( 222.23) N ,and for Ball (394.64) N for right side, for left side average, microstrain for Ball (391.26) N , and for CMLOC (223.22) N . When the load applied bilaterally, the single implant retained ovcrdenturc with the CMLOC (269.05)N attachment has shown higher microstrain than the Ball (106.79)
Tags from this library: No tags from this library for this title. Log in to add tags.
Star ratings
    Average rating: 0.0 (0 votes)
Holdings
Item type Current library Home library Call number Copy number Status Date due Barcode
Thesis Thesis قاعة الرسائل الجامعية - الدور الاول المكتبة المركزبة الجديدة - جامعة القاهرة Cai01.09.09.M.Sc.2020.Ah.S (Browse shelf(Opens below)) Not for loan 01010110082724000
CD - Rom CD - Rom مخـــزن الرســائل الجـــامعية - البدروم المكتبة المركزبة الجديدة - جامعة القاهرة Cai01.09.09.M.Sc.2020.Ah.S (Browse shelf(Opens below)) 82724.CD Not for loan 01020110082724000

Thesis (M.Sc.) - Cairo University - Faculty of Oral and Dental Medicine - Department of Prosthodontics

Aim: The aim of this in vitro study is to record the induced micro-strain around one installed implant in the midline of a completely edentulous mandible using strain gauges utilizing an implant retained overdenture with two different types of attachments Ball and CMLOC attachment. Methodology : An acrylic resin test resin test model representing a completely edentulous lower arch was used The distal part of the residual ridge was covered with silicon based soft liner to stimulate the mucopcriostcum. Steps of complete denture fabrication was followed in conventional manner .Duplication of the finished denture was carried out to be used as a surgical stent .A single implant installed in the midline.After the implant was installed in the acrylic resin cast, the ball attachment was screwed to the implant.The denture was prepared for the direct pick up procedure, the same procedure repeated for CM IOC attachment. Four strain gauges around were installed on all surfaces of implant (Buccal. Lingual. Mesial .Distal) to monitor the effect of the applied loads vertical on the two types of attachments. A vertically load applied of 100 N static load was applied by using universal testing machine at three different sites (unilateral right first molar central fossa, left first molar and bilaterally. Results: When the load applied on the right side and left side ,it was shown that the single implant retained ovcrdenture with ball the attachment has shown higher microstrain than the CMLOC ,average microstrain for CMLOC ( 222.23) N ,and for Ball (394.64) N for right side, for left side average, microstrain for Ball (391.26) N , and for CMLOC (223.22) N . When the load applied bilaterally, the single implant retained ovcrdenturc with the CMLOC (269.05)N attachment has shown higher microstrain than the Ball (106.79)

Issued also as CD

There are no comments on this title.

to post a comment.