Adaptation of resilion and protaper-universal Obturators versus warm vertically compacted gutta-percha in filling induced resorptive apical defect : An in vitro study /
Mennah Tollah Mohamed Mostafa Nagdy
Adaptation of resilion and protaper-universal Obturators versus warm vertically compacted gutta-percha in filling induced resorptive apical defect : An in vitro study / ملائمة الريزليون و البروتابر العالمى المستخدم فى غلق قناة الجذر مقارنة بالجتابركا المكبوسة عموديا باستخدام الحرارة فى حشو تآكل قمى مفتعل Mennah Tollah Mohamed Mostafa Nagdy ; Supervised Hebatollah Mohamed Maged Elfar , Geraldine Mohamed Ahmed - Cairo : Mennah Tollah Mohamed Mostafa Nagdy , 2014 - 117 P. : facsimiles , photographs ; 25cm
Thesis (M.Sc.) - Cairo University - Faculty of Oral and Dental Medicine - Department of Endodontics
The aim of the present study was to evaluate and compare the obturation of the induced apical resorptive cavities using: New protaper-universal obturators and warm vertical condensation of resilon epiphany system versus warm vertical condensation of gutta-percha\AH-plus. Sixty freshly extracted single canalled human teeth were prepared. The teeth were immersed in 5.25% NaOCl for one hour to remove any tissue adhering to the root surface. A part of the crown was removed to get a standard length of 19mm. Access cavity was prepared. Canal length was established by placing #15 K file into each root canal until the tip of the file became visible at the tip of the apical foramen. Working length was established 1mm short of the apex. The canal was cleaned and shaped by protaper instruments using crown-down technique. 5.25% NaOCl was used as a lubricant during preparation. The smear layer was removed by using 17% EDTA followed by 5.25% NaOCl. All canals were finally flushed using distilled water. Root canals were dried with paper points. Experimental Internal Resorptive Cavities (IRC) were created by sectioning at about 7mm from the apex using carborundum discs. Semicircular cavities were created around the periphery of the opening of the root canal of each section using low speed hand piece and #6 round bur. Sections were repositioned together and cemented using glue. Each tooth was embedded in a plaster cast. Prepared teeth were randomly divided into three groups each containing 20 teeth, according to the obturation materials and techniques
Protaper Resilion Universal
Adaptation of resilion and protaper-universal Obturators versus warm vertically compacted gutta-percha in filling induced resorptive apical defect : An in vitro study / ملائمة الريزليون و البروتابر العالمى المستخدم فى غلق قناة الجذر مقارنة بالجتابركا المكبوسة عموديا باستخدام الحرارة فى حشو تآكل قمى مفتعل Mennah Tollah Mohamed Mostafa Nagdy ; Supervised Hebatollah Mohamed Maged Elfar , Geraldine Mohamed Ahmed - Cairo : Mennah Tollah Mohamed Mostafa Nagdy , 2014 - 117 P. : facsimiles , photographs ; 25cm
Thesis (M.Sc.) - Cairo University - Faculty of Oral and Dental Medicine - Department of Endodontics
The aim of the present study was to evaluate and compare the obturation of the induced apical resorptive cavities using: New protaper-universal obturators and warm vertical condensation of resilon epiphany system versus warm vertical condensation of gutta-percha\AH-plus. Sixty freshly extracted single canalled human teeth were prepared. The teeth were immersed in 5.25% NaOCl for one hour to remove any tissue adhering to the root surface. A part of the crown was removed to get a standard length of 19mm. Access cavity was prepared. Canal length was established by placing #15 K file into each root canal until the tip of the file became visible at the tip of the apical foramen. Working length was established 1mm short of the apex. The canal was cleaned and shaped by protaper instruments using crown-down technique. 5.25% NaOCl was used as a lubricant during preparation. The smear layer was removed by using 17% EDTA followed by 5.25% NaOCl. All canals were finally flushed using distilled water. Root canals were dried with paper points. Experimental Internal Resorptive Cavities (IRC) were created by sectioning at about 7mm from the apex using carborundum discs. Semicircular cavities were created around the periphery of the opening of the root canal of each section using low speed hand piece and #6 round bur. Sections were repositioned together and cemented using glue. Each tooth was embedded in a plaster cast. Prepared teeth were randomly divided into three groups each containing 20 teeth, according to the obturation materials and techniques
Protaper Resilion Universal